key features: ? operates with xx962 drivers ? independent outputs ? 3,000 vac isolation ? miniature sip case ? >3.5 mhour mtbf ? 5 standard models ? low cost!! ig100 high isolation igbt driver dc/dc con vert ers series input parameter conditions min. typ. max. units supply voltage range see model selection guide input filter internal capacitor output parameter conditions min. typ. max. units line regulation, see note 1 for vin change of 1% 1.3 1.5 % ripple & noise (20 mhz) ig120-12 100 200 mv p - p ig120-12w 100 200 ig120-15 80 150 IG135-15 50 150 ig120-24 150 300 ef? ciency 80 % output short circuit, see note 3 continuous (autorecovery) general parameter conditions min. typ. max. units isolation voltage 60 seconds 3,000 vac isolation resistance 1,000 m isolation capacitance, 1 khz/1v ig120-12 6.6 pf ig120-12w 10 ig120-15 6.6 IG135-15 8.0 10 ig120-24 6.6 switching frequency 550 khz environmental parameter conditions min. typ. max. units operating temperature range ambient -40 +25 +85 oc storage temperature range -50 +125 oc cooling free air convection humidity rh, non-condensing 95 % physical case size 0.768 x 0.386 x 0.492 inches (19.50 x 9.80 x 12.50 mm) case material non-conductive black plastic (ul94-v0) weight 0.195 oz (5.5g) reliability speci cations parameter conditions min. typ. max. units mtbf mil hdbk 217f, 25oc, gnd benign 3.5 mhours absolute maximum ratings parameter conditions min. typ. max. units max supply voltage (1 sec) ig120-12 13 vdc ig120-12w 15 ig120-15 16 IG135-15 16 ig120-24 26 lead temperature 1.5 mm from case for 10 sec 300 oc caution: exceeding absolute maximum ratings may damage the module. these are not continuous operating ratings. electrical speci cations speci cations typical @ +25?, nominal input voltage & rated output current, unless otherwise noted. speci cations subject to change without notice. www.micropowerdirect.com micropower direct 292 page street suite d stoughton, ma 02072 usa t: (781) 344-8226 f: (781) 344-8481 e: sales@micropowerdirect.com w: www.micropowerdirect.com www.datasheet.net/ datasheet pdf - http://www..co.kr/
notes: all dimensions are typical in inches (mm) tolerance x.xx = 0.01 ( 0.25) pin 1 is marked by a ?ot or indentation on the side of the unit model number input (supply) output 1 output 2 output load regulation (%) maximum capacitive load (f) fuse rating slow-blow (ma) voltage (vdc) voltage (vdc) current (ma max) current (ma, min) voltage (vdc) current (ma max) current (ma, min) nom. range min. nom. max. min. nom. max. ig120-12 12 11.6 - 12.4 14.0 15.0 16.0 80.0 0.0 -7.0 -9.0 -10.0 40.0 0.0 12 470 1,000 ig120-12w 12 9.0 - 15.0 14.0 15.0 16.0 100.0 0.0 -7.0 -8.0 -9.0 80.0 0.0 12 470 1,000 ig120-15 15 14.5 - 15.5 14.0 15.0 16.0 80.0 0.0 -7.0 -8.7 -10.0 40.0 0.0 18 470 1,000 ig136-15 15 14.5 - 15.5 16.5 17.0 18.0 80.0 0.0 -7.0 -8.7 -10.0 40.0 0.0 18 470 1,000 ig120-24 24 23.3 - 24.7 14.0 15.0 16.0 80.0 0.0 -7.0 -9.0 -10.0 40.0 0.0 12 470 1,000 pin function 1+vin 2 gnd 5 vout 2 6 common 7 vout 1 typical connection y p notes: 1. line regulation for model ig120-12w is given for a v in change of 25%. 2. load regulation is measured from 10% load to full load. load regulation is speci? ed for the primary output (output 1). load regulation of output 2 may vary slightly. 3. operation at no-load will not damage these units. however, they may not meet all speci? cations. 4. if output 2 is not used, it should be left open. 5. a short circuit fault that lasts over 10 minutes could damage the unit due to an over temperature fault. 6. it is recommended that a fuse be used on the input of a power supply for protection. see the model selection table above for the correct rating. connection notes: 1. for model ig120-24, c 1 is a 100 f/65v. 2. capacitors c 1 , c 2 and c 3 should be mounted as close to the unit as possible. to ensure peak gate current, these capacitors should have a low esr. 3. the trace (or wire) between the dc/dc and the driver circuit should be as short as possible. 4. the average output power of the driver circuit must be lower than output power of the dc/dc. the ig100 series is designed to operate with the igd962 igbt driver. model selection guide mechanical dimensions pin connections micropower direct we power your success - for less! 292 page street ste d stoughton, ma 02072 ? tel: (781) 344-8226 ? fax: (781) 344-8481 ? e-mail: sales@micropowerdirect.com www.micropowerdirect.com www.datasheet.net/ datasheet pdf - http://www..co.kr/
|
